View AD9835EB_4202085.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

a
FEATURES Full-Featured Evaluation Board for the AD9835 Various Linking Options PC Software for Control of AD9835 On-Board Patchwork Area INTRODUCTION
Evaluation Board for the AD9835 Direct Digital Synthesizer EVAL-AD9835EB
Components on the AD9835 Evaluation Board include a 50 MHz oscillator which provides the MCLK for the AD9835. The user can remove this oscillator, if required, and drive the AD9835 with a different clock oscillator or an external clock source via a BNC connector. A digital buffer is also on the board so that the signals from the edge connector are buffered.
This Application Note describes the evaluation board for the AD9835 Direct Digital Synthesizer (DDS). The AD9835 is a numerically controlled oscillator employing a phase accumulator, a sine look-up table and a 10-bit D/ A converter. The part can be operated with clock frequencies up to 50 MHz. Both phase modulation and frequency modulation can be performed with the AD9835. Full data on the AD9835 is available in the AD9835 datasheet available from Analog Devices and should be consulted in conjunction with this Application Note when using the evaluation board. The evaluation board interfaces to the parallel port of an IBM compatible PC. Software is available with the evaluation board which allows the user to easily program the AD9835.
OPERATING THE AD9835 EVALUATION BOARD Power Supplies
This evaluation board has two analog power supply inputs: AVDD and AGND. AVDD equals +5V or +3.3V and is used to provide the AVDD for the AD9835. DGND and DVDD connections are also available. The DVDD is used to provide the DVDD for the AD9835, the 50 MHz oscillator and the DVDD for the digital buffer. DGND and AGND are connected under the AD9835. Therefore, it is recommended not to connect AGND and DGND elsewhere in the system. All power supplies are decoupled to ground. AVDD and DVDD are decoupled using 10F tantalum capacitors and 0.1F ceramic capacitors at the input to the evaluation board. The power supplies are again decoupled using 0.1F capacitors at the AD9835, the crystal and the logic.
Figure 1: Evaluation Board Setup
IB M C o m p a tib le P C P a ra lle l P o rt C e n tro n ics P rin te r C a b le
AD 98 35 .E XE
AD 9835 E valuation B oard
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
One Technology Way; P.O.BOX 9106; Norwood, MA 02062-9106 U.S.A. Tel: 617/329-4700 Twx: 710/394-6577 Telex: 174059 Cables: ANALOG NORWOOD MASS
Rev. A
EVAL-AD9835EB
LINK AND SWITCH OPTIONS
There are four link options which must be set for the required operating setup before using the evaluation board. functions of these link options are outlined below.
Link No. Function
The
LK1
When SELSRC = 0, the PSEL1 input can be controlled by the user via a SMB connector or alternatively, by switch SW1-2. With LK1 in position "A", PSEL1 can be controlled from an external logic source through the SMB connector, PSEL1. With LK1 in position"B" PSEL1 is connected to SW1, allowing the user to control the PSEL1s i g n a l using the double throw switch, SW1-2.
LK2
When SELSRC = 0, the PSEL0 input can be controlled by the user via a SMB connector or alternatively, by switch SW1-1. With LK2 in position "A", PSEL0 can be controlled from an external logic source through the SMB connector, PSEL0. With LK2 in position"B" PSEL0 is connected to SW1, allowing the user to control the PSELOs i g n a l using the double throw switch, SW1-1.
LK3
When SELSRC = 0, the FSELECT input can be controlled by the user via a SMB connector or alternatively, by switch SW1-3. With LK3 in position "A", FSELECT can be controlled from an external logic source through the SMB connector, FSEL1. With LK3 in position"B" FSELECT is connected to SW1, allowing the user to control the FSELECT signal using the double throw switch, SW1-3.
LK4
The reference to the AD9835 can be provided by the on-board reference, which is available at REFOUT, or an external reference of nominal value 1.21 V can be used. When LK4 is closed, the on-board reference is used. When this link is opened, REFIN is disconnected from REFOUT and the reference must be provided by the user via the SMB connector, REFIN1.
SET-UP CONDITIONS
Care should be taken before applying power and signals to the evaluation board to ensure that all link positions are as per the required operating mode. Table 1 shows the position in which all the links are set when the evaluation board is packaged.
Table 1: Initial Link and Switch Positions Link No. Position Function
LK1 LK2 LK3 LK4 SW1
B B B IN DVDD
LK1 is arranged so that PSEL1 is tied to SW1-2. LK2 is arranged so that PSEL0 is tied to SW1-1. LK3 is arranged so that FSELECT is tied to SW1-3. REFOUT is tied to REFIN. All the SW1 switches are arranged so that DVDD is selected.
-2-
Rev. A
EVAL-AD9835EB
EVALUATION BOARD INTERFACING SOCKETS
Interfacing to the evaluation board is via a 36-way centronics female connector, J1. The pinout for the J1 connector is shown in Figure 2 and its pin designations are given in Table 2.
There are six sockets relevant to the operation of the AD9835 on this evaluation board. The function of these sockets is outlined in Table 3.
18
1
Table 3. Socket Functions Socket Function
36
19
REFIN IOUT MCLK
Sub-Miniature BNC Socket for REFIN. Sub-Miniature BNC Socket for IOUT. Sub-Miniature BNC Socket for the MCLK input. Sub-Miniature BNC Socket for FSELECT. Sub-Miniature BNC Socket for PSEL0. Sub-Miniature BNC Socket for PSEL1.
Figure 2: Pin Configuration for 36-Way Connector, J1. 36-Way Connector Pin Description
FSEL PSEL0 PSEL1
DGND
Digital Ground. These lines are connected to the digital ground plane on the evaluation board. Serial Data. Data applied to this pin is buffered before being applied to the AD9835. The serial data applied to the SDATA pin is written to the serial register of the device. The data is then transferred to the destination register, the control register or the FSELECT/PSEL registers, the control bits being used to identify the destination for the data information. The AD9835 accepts CMOS logic levels. Serial Clock. The signal on this pin is buffered before being applied to the SCLK pin of the AD9835. The AD9835 requires an external serial clock when data/control information is being written to the device. The serial clock can be continuous or, it can idle high or low between write operations. The signal on this pin is buffered before being applied to the FSYNC pin of the AD9835. The FSYNC signal frames the 16-bit word being loaded into the AD9835, the signal going low for 16 SCLK cycles.
SDATA
CONNECTORS
There are three connectors on the AD9835 evaluation board as outlined in Table 4.
Table 4. Connector Functions
Connector Functions
SCLK
J1 J2
36-Way Centronics Connector. PCB Mounting Terminal Block. The Digital Power Supply to the Evaluation Board is provided via this Connector. PCB Mounting Terminal Block. The Analog Power Supply to the Evaluation Board is provided via this Connector.
FSYNC
J3
SWITCHES Table 2. 36-Way Connector Pin Funtions
PIN NO. 2 3 4 19-30
MNEMONIC SCLK SDATA FSYNC DGND
There is one switch on the AD9835 evaluation board. This switch is a double throw, end stackable switch. This switch can be used to control the FSELECT, PSEL0 and PSEL1 inputs.
Note: The remainder of the pins on the 36-way connector are no connects.
-3-
Rev. A
EVAL-AD9835EB
SOFTWARE DESCRIPTION
The AD9835 evaluatmon board comes with a floppy disk containing software that allows the user to control the AD9835 from an IBM compatible PC. The PC is connected to the evaluation board by a standard CentronicsTM printer cable.
Installing the Software:
The software will run on any IBM compatible PC which meets the following requirements. * Microsoft Windows 3.1 or Windows95 installed. * 80386 or higher processor. * At least 1.5 Mb of free hardisk space. The software is distributed on a single 3.5 inch diskette. The diskette contains all the files required to install and run the software. Using either the Program Manager or the File Manager the user should select the floppy drive ( usually a:) and double click on the SETUP.EXE file. This program simplifies the installation of the software by copying the files from the diskette to the relevant directories on the hard disk.
When the setup program is running the user will be prompted to enter a destination directory for the software. A default directory is given as C:\AD9835. When the software is installed a Windows Group called Analog Devices will be created (Windows 3.1 only) and the AD9835 icon will be placed there. Double clicking on this icon will run the evaluation software. Windows 95 users can navigate through the directories using Windows Explorer and then double click on the AD9835.EXE file to start the software.
The Evaluation Software
When the program starts it will check the PC BIOS to detect the address of the printer port installed. There are three possible base addresses at which a printer port can reside and these are shown below together with the printer names. PrinterBase Address (hex) LPT1 LPT2 PRN1 0x378 0x278 0x3BC
If there is more than one printer port installed the software will chose the first one it finds. It is possible to change the printer port from the software by clicking the Select Port button. The main screen for the evaluaton board software is shown in Fig. 3 below.
Figure 3: The Main Screen
-4-
Rev. A
EVAL-AD9835EB
Features of the AD9835 Evaluation Board Software The SELSRC Bit
The software allows the user to control all the functionality of the AD9835. The main features are listed below. * Access to both Frequency 0 and Frequency 1 registers * Access to the Phase Reg. 0, Phase Reg. 1, Phase Reg. 2 and Phase Reg. 3 * Access to Sleep, Reset and SELSRC bits. * Ability to sweep through a frequency range using either the Frequency 0 or Frequency 1 registers. Each of these features is described in detail in this application note.
The Frequency Registers
The SELSRC bit of the AD9835 is used to control the selection of the frequency and phase registers used to provide the output. If this bit is a zero the frequency and phase selection comes from FSELECT, PSEL0 and PSEL1 pins respectively. If the bit is a 1 then the registers are selected by software. Pressing the SELSRC button toggles this bit on the AD9835 and also enables or disables changing the frequency and phase registers from software as required. It should be noted that since there is no readback facility on the AD9835 it is not possible to determine the contents of any register which has not been programmed by the software. For this reason selecting a frequency or phase register which hasn't been programmed may give an unpredicted output.
The Sweep Facility
The AD9835 contains 2 frequency registers which can be programmed individually. The software allows the user to enter any frequency value between 0Hz and half the master clock frequency. If a value outside this range is entered the software picks the closest valid value. The frequency value is converted to a 32 bit hexidecimal number which is loaded to the appropriate frequency register when the enter key is pressed. The hexidecimal number is also displayed on the main screen.
The Phase Registers
Pressing the Sweep button displays a new screen which can be used to program the AD9835 to produce a continuously increasing or decreasing frequency sweep. The user has the option of entering a start frequency, a stop frequency and a step frequency. There is also the option of setting the delay between steps and the number of time the sweep is to be repeated. If the user were to enter the sweep values shown below then the frequency outputs also shown below will be generated. Note that if the frequency span is not an integer multiple of the step frequency then the span from the second last frequency to the last frequency will be such that the stop frequency is the last frequency outputed to the AD9835. Start Freq. Stop Freq. Step Freq. Frequency Outputs: 1.00000MHz 1.70000MHz 0.20000MH 1.00000MHz 1.20000MHz 1.40000MHz 1.60000MHz 1.70000MHz Both Frequency Register 0 and Frequency Register 1 can be loaded with seperate frequency, step, delay and loop information but the output from the AD9835 will depend on which frequency register is selected via the FSELECT pin. If changing the frequency register is required then the user should ensure that the SELSRC bit is zero before starting the sweep.
Additional Information
The AD9835 contains four phase register which can be individually loaded with different values. The phase numbers are entered as integer values between 0 and 4095 (corresponding to 0 to 360 phase shift). Once again the values are loaded to the appropriate phase register when the enter key is pressed.
Normal/Sleep Mode
The Control Register of the AD9835 contains a sleep bit to put the part into a power-down mode. When this bit is a logic 1 the internal clocks are disabled and the DAC's current sources and REFOUT are turned off. This bit can be controlled by the two radio buttons in the Normal/Sleep Mode box. The software defaults to Normal Mode reflecting the reset state of the AD9835.
Reset Mode
The Reset bit in the Control Register of the AD9835 is controllable by the RESET button of the AD9835 Evaluation Board Software. Pressing this button toggles the state of the bit in the control register. Note that it is assummed that the RESET bit is low when the software is started. Setting the RESET bit to 1 will set the phase accumulator to zero phase corresponding to a full scale output.
Information about the current version of software can be gathered from the About Screen (accessed by pressing the About button on the main screen).
-5-
Rev. A
EVAL-AD9835EB
-6Figure 4: Eval-AD9835EB Schematic
Rev. A
EVAL-AD9835EB
Table 5. Component Listing
Item Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 1 1 1 7 1 2 3 1 1 1 6 1 3 1 4 1 1 1 4
Reference U1 U2 SW1 XTAL1 C1 C2 C4 C5 C6 C7 C9 C3 C8 C10 R1 R2 R3 R4 R5 R6
PSEL1PSEL0FSELCLKIOUTREFIN
Description AD9835 74HCT244 Double throw end stackable switch 50MHZ CMOS/TTL Crystal 100nF Ceramic Capacitor 10nF ceramic Capacitor 10uF Tantalum Capacitor 10KW Resistor 51KW Resistor 3.9KW Resistor 300W Resistor Sub Miniature BNC connector 36 Way Centronics Connector 3 pin sil header 2 pin sil header jumper 20 pin dil solder socket 14 pin dil solder socket Two Way Terminal Block Each corner
Supplier / No. ADI AD9835 FEC 382-267 FEC 422-708 FEC 571-842 FEC 146-227 FEC 146-224 FEC 643-683 FEC 543-627 FEC 543-070 FEC 543-524 FEC 543-251 FEC 299-844 FEC 147-753 FEC 528-432 FEC 528-432 FEC 150-410 FEC 738-554 FEC 738-529 FEC 151-789 FEC 148-922
J1 Lk1 Lk2 Lk3 Lk4 Lk1 Lk2 Lk3 Lk4 U2 XTAL1 J2 J3 Rubber-Stick-On feet
Figure 5. Eval-AD9835EB Silkscreen Artwork
-7-
Rev. A
EVAL-AD9835EB
Figure 6. Eval-AD9835EB Component Side Artwork
Figure 7. Eval-AD9835EB Solder Side Artwork
-8-
Rev. A

▲Up To Search▲

Price & Availability of AD9835EB

	To Download AD9835EB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .